|
|
Design of test rig for long-term testing of couplings intended for railroad applications
Machálek, Ondřej ; Prokop, Aleš (referee) ; Řehák, Kamil (advisor)
The master thesis deals with design of test rig for long-term testing of coupling appointed to railway vehicles. At first, there is made a brief research which is related to railway coupling used for transmitting a torque. This is followed by an analysis of the most used power devices to derive real loads conditions of tested couplings. There is chosen the most appropriate conception based on made analysis and it is followed by the description of designed components. There is made a verification of modal properties non-purchased components which is necessary part of the thesis. Numerical modal analysis was performed in ANSYS Workbench software. In the end of the thesis there are included stress-strain analysis of the chosen designed components.
|
|
|
Stroke mechanism of bridge crane
Jirásek, Jiří ; Kašpárek, Jaroslav (referee) ; Škopán, Miroslav (advisor)
This bachelor thesis deals with the design of the lifting mechanism of the crane cat, for a bridge storage crane with a load capacity of 8,000 kg. The thesis contains a critical research of similar existing solutions and the selection of the appropriate concept. The design includes calculations of the basic parameters of the stroke, and based on them selects appropriate rope, pulleys, and design of the rope drum. Furthermore, there are calculated and selected suitable components of the stroke mechanism such as electric motor, clutch, brake and gearbox. The last part deals with the design of the bearing, the drum pin and the calculation of the shaft key. The output of the work is the technical drawing of the whole assembly of the mechanism and the welding subassembly of the rope drum.
|
|
|
Automobile clutches
Kundýsek, Michal ; Píštěk, Václav (referee) ; Kaplan, Zdeněk (advisor)
This bachelor thesis provides an overview of the various types of clutch and starting clutch technologies, before offering a detailed analysis of the friction clutch system. It addresses the relative merits of this particular type of clutch and concludes with a discussion of its contemporary automotive applications.
|
|
|
Single cylinder engines enduro category
Svoboda, Tomáš ; Beran, Martin (referee) ; Vančura, Jan (advisor)
Bachelor thesis deals with the description of typical enduro motorcycle engine and describes its main parts. Next volume concern about chosen types of enduro motorcycles and its en-gines. Achievement of every single engine is shown in dynamometric diagrams. Maintenance schedule which is affected by given achievements is shown in tables. The engines of enduro motorcycles have been partly compared with motocross motorcycle engines
|
|
|
Optimization of the existing construction of magnetorheological clutch
Bedřich, Miroslav ; Růžička, Bronislav (referee) ; Roupec, Jakub (advisor)
This work deals with the reconstruction of magnetorheological (MR) clutch. The extensive research on the use of magnetorheological technology in practice was developed in the first part. The function of MR dampers, MR brakes and MR clutches were described. Some parameters of MR clutches were listed and compared. The second part concentrates on construction modifications to improve some parameters of MR clutch. The experiments verifying improvement of operating parameters of MR clutch were carried out in the third part.
|
|
|
Study of torque vectoring clutch design
Cupák, Václav ; Porteš, Petr (referee) ; Fojtášek, Jan (advisor)
This work deals with the design of right and left torque vectoring control used in heavy commercial vehicle powertrains. The beginning of the work is focused on the description of the active differential system and on the clutches used in the automotive industry. Then the basic parameters of the experimental vehicle are defined and the choice of the clutch conception is made. Subsequently, calculations of geometric parameters of clutches and verification of their heat capacity is made. Conceptual design of the control mechanism is discussed in the last chapter. The aim of the work is the draft of the possible type of control mechanism for the given system with the possibility to use the information obtained for the further development of this system.
|
|
|
Stroke mechanism of crane trolley
Galas, Radovan ; Malášek, Jiří (referee) ; Škopán, Miroslav (advisor)
Bachelor's thesis deals with design of stroke mechanism of crane trolley loads for the weights which do not exceed 5 000 kg. This thesis divided into written and practical sections. Written part deals with the calculation of the principal dimensions of lifting and stress control of cable reel. In this work there are also given reasons for choosing certain key parts of the lifting mechanism, such as: electric motor, gearbox, etc. Prior to the calculations in each chapter there is usually located a short introduction of the topic. The practical part contains a drawing of the complete lifting mechanism, cable reel assembly and two production drawings.
|
|
|
Influence of physical parameters and age of power lines on PCL/BPL performance and reliability
Janás, Jan ; Mlýnek, Petr (referee) ; Benešl, Lukáš (advisor)
With the increasing demands on data transmission, other ways are being sought than standard data transmission via conventional data cables. One of these ways is communication over power lines - PLC or BPL technology. This method of communication is widely used in households, energy, industry and other fields where it is used for data collection, communication, or control of various devices. Before considering the use of BPL technology, it is first necessary to evaluate the considered power line to see if it is suitable and technically competent for this purpose.
|
|
|
Solution technology of manufacturing for part "disc of coupler"
Borek, Vít ; Osička, Karel (referee) ; Mouralová, Kateřina (advisor)
An introduction to main principles of coupling and description of basic types has been done. An analysis of the given component and a proposal for suitable intermediate was made. A selection of machines and tools for individual operations has been done. A proposition of technologic process and enumeration of machines times was proposed. Economic evaluation containing costs for tools, cooperation, workmen’s wages, intermediate and energy for operating machines has been calculated.
|
|
|
Design of wind power plant
Starý, Ondřej ; Dlugoš, Jozef (referee) ; Řehák, Kamil (advisor)
Renewable energy sources are currently a much-discussed issue. One of the possibilities of their use is the production of electricity using wind power plants. This work therefore describes in detail construction of wind turbines. At the same time, there is a brief evaluation of wind power plants, from an energy and economic point of view. Part of the work is also the calculation of the optimization of the gearbox weight and a description of the design of the wind turbine coupling.
|
guest ::
